325 lines
11 KiB
Plaintext
Executable File
325 lines
11 KiB
Plaintext
Executable File
# Generated by PNCconf at Sat Aug 3 03:07:39 2024
|
|
# Using LinuxCNC version: Master (2.9)
|
|
# If you make changes to this file, they will be
|
|
# overwritten when you run PNCconf again
|
|
|
|
loadrt [KINS]KINEMATICS
|
|
loadrt [EMCMOT]EMCMOT servo_period_nsec=[EMCMOT]SERVO_PERIOD num_joints=[KINS]JOINTS
|
|
loadrt hostmot2
|
|
loadrt hm2_pci config="num_encoders=1 num_pwmgens=0 num_stepgens=5 sserial_port_0=00xxxxxx"
|
|
setp hm2_5i25.0.watchdog.timeout_ns 5000000
|
|
loadrt pid names=pid.x,pid.y,pid.z,pid.s
|
|
loadrt mux16 names=jogincr,foincr,mvoincr,soincr
|
|
|
|
addf hm2_5i25.0.read servo-thread
|
|
addf motion-command-handler servo-thread
|
|
addf motion-controller servo-thread
|
|
addf pid.x.do-pid-calcs servo-thread
|
|
addf pid.y.do-pid-calcs servo-thread
|
|
addf pid.z.do-pid-calcs servo-thread
|
|
addf pid.s.do-pid-calcs servo-thread
|
|
addf jogincr servo-thread
|
|
addf foincr servo-thread
|
|
addf mvoincr servo-thread
|
|
addf soincr servo-thread
|
|
addf hm2_5i25.0.write servo-thread
|
|
setp hm2_5i25.0.dpll.01.timer-us -50
|
|
setp hm2_5i25.0.stepgen.timer-number 1
|
|
|
|
# external output signals
|
|
|
|
|
|
# external input signals
|
|
|
|
|
|
#*******************
|
|
# AXIS X JOINT 0
|
|
#*******************
|
|
|
|
setp pid.x.Pgain [JOINT_0]P
|
|
setp pid.x.Igain [JOINT_0]I
|
|
setp pid.x.Dgain [JOINT_0]D
|
|
setp pid.x.bias [JOINT_0]BIAS
|
|
setp pid.x.FF0 [JOINT_0]FF0
|
|
setp pid.x.FF1 [JOINT_0]FF1
|
|
setp pid.x.FF2 [JOINT_0]FF2
|
|
setp pid.x.deadband [JOINT_0]DEADBAND
|
|
setp pid.x.maxoutput [JOINT_0]MAX_OUTPUT
|
|
setp pid.x.error-previous-target true
|
|
# This setting is to limit bogus stepgen
|
|
# velocity corrections caused by position
|
|
# feedback sample time jitter.
|
|
setp pid.x.maxerror 0.000500
|
|
|
|
net x-index-enable => pid.x.index-enable
|
|
net x-enable => pid.x.enable
|
|
net x-pos-cmd => pid.x.command
|
|
net x-pos-fb => pid.x.feedback
|
|
net x-output <= pid.x.output
|
|
|
|
# Step Gen signals/setup
|
|
|
|
setp hm2_5i25.0.stepgen.00.dirsetup [JOINT_0]DIRSETUP
|
|
setp hm2_5i25.0.stepgen.00.dirhold [JOINT_0]DIRHOLD
|
|
setp hm2_5i25.0.stepgen.00.steplen [JOINT_0]STEPLEN
|
|
setp hm2_5i25.0.stepgen.00.stepspace [JOINT_0]STEPSPACE
|
|
setp hm2_5i25.0.stepgen.00.position-scale [JOINT_0]STEP_SCALE
|
|
setp hm2_5i25.0.stepgen.00.step_type 0
|
|
setp hm2_5i25.0.stepgen.00.control-type 1
|
|
setp hm2_5i25.0.stepgen.00.maxaccel [JOINT_0]STEPGEN_MAXACCEL
|
|
setp hm2_5i25.0.stepgen.00.maxvel [JOINT_0]STEPGEN_MAXVEL
|
|
|
|
# ---closedloop stepper signals---
|
|
|
|
net x-pos-cmd <= joint.0.motor-pos-cmd
|
|
net x-vel-cmd <= joint.0.vel-cmd
|
|
net x-output => hm2_5i25.0.stepgen.00.velocity-cmd
|
|
net x-pos-fb <= hm2_5i25.0.stepgen.00.position-fb
|
|
net x-pos-fb => joint.0.motor-pos-fb
|
|
net x-enable <= joint.0.amp-enable-out
|
|
net x-enable => hm2_5i25.0.stepgen.00.enable
|
|
|
|
# ---setup home / limit switch signals---
|
|
|
|
net x-home-sw => joint.0.home-sw-in
|
|
net x-neg-limit => joint.0.neg-lim-sw-in
|
|
net x-pos-limit => joint.0.pos-lim-sw-in
|
|
|
|
#*******************
|
|
# AXIS Y JOINT 1
|
|
#*******************
|
|
|
|
setp pid.y.Pgain [JOINT_1]P
|
|
setp pid.y.Igain [JOINT_1]I
|
|
setp pid.y.Dgain [JOINT_1]D
|
|
setp pid.y.bias [JOINT_1]BIAS
|
|
setp pid.y.FF0 [JOINT_1]FF0
|
|
setp pid.y.FF1 [JOINT_1]FF1
|
|
setp pid.y.FF2 [JOINT_1]FF2
|
|
setp pid.y.deadband [JOINT_1]DEADBAND
|
|
setp pid.y.maxoutput [JOINT_1]MAX_OUTPUT
|
|
setp pid.y.error-previous-target true
|
|
# This setting is to limit bogus stepgen
|
|
# velocity corrections caused by position
|
|
# feedback sample time jitter.
|
|
setp pid.y.maxerror 0.000500
|
|
|
|
net y-index-enable => pid.y.index-enable
|
|
net y-enable => pid.y.enable
|
|
net y-pos-cmd => pid.y.command
|
|
net y-pos-fb => pid.y.feedback
|
|
net y-output <= pid.y.output
|
|
|
|
# Step Gen signals/setup
|
|
|
|
setp hm2_5i25.0.stepgen.01.dirsetup [JOINT_1]DIRSETUP
|
|
setp hm2_5i25.0.stepgen.01.dirhold [JOINT_1]DIRHOLD
|
|
setp hm2_5i25.0.stepgen.01.steplen [JOINT_1]STEPLEN
|
|
setp hm2_5i25.0.stepgen.01.stepspace [JOINT_1]STEPSPACE
|
|
setp hm2_5i25.0.stepgen.01.position-scale [JOINT_1]STEP_SCALE
|
|
setp hm2_5i25.0.stepgen.01.step_type 0
|
|
setp hm2_5i25.0.stepgen.01.control-type 1
|
|
setp hm2_5i25.0.stepgen.01.maxaccel [JOINT_1]STEPGEN_MAXACCEL
|
|
setp hm2_5i25.0.stepgen.01.maxvel [JOINT_1]STEPGEN_MAXVEL
|
|
|
|
# ---closedloop stepper signals---
|
|
|
|
net y-pos-cmd <= joint.1.motor-pos-cmd
|
|
net y-vel-cmd <= joint.1.vel-cmd
|
|
net y-output => hm2_5i25.0.stepgen.01.velocity-cmd
|
|
net y-pos-fb <= hm2_5i25.0.stepgen.01.position-fb
|
|
net y-pos-fb => joint.1.motor-pos-fb
|
|
net y-enable <= joint.1.amp-enable-out
|
|
net y-enable => hm2_5i25.0.stepgen.01.enable
|
|
|
|
# ---setup home / limit switch signals---
|
|
|
|
net y-home-sw => joint.1.home-sw-in
|
|
net y-neg-limit => joint.1.neg-lim-sw-in
|
|
net y-pos-limit => joint.1.pos-lim-sw-in
|
|
|
|
#*******************
|
|
# AXIS Z JOINT 2
|
|
#*******************
|
|
|
|
setp pid.z.Pgain [JOINT_2]P
|
|
setp pid.z.Igain [JOINT_2]I
|
|
setp pid.z.Dgain [JOINT_2]D
|
|
setp pid.z.bias [JOINT_2]BIAS
|
|
setp pid.z.FF0 [JOINT_2]FF0
|
|
setp pid.z.FF1 [JOINT_2]FF1
|
|
setp pid.z.FF2 [JOINT_2]FF2
|
|
setp pid.z.deadband [JOINT_2]DEADBAND
|
|
setp pid.z.maxoutput [JOINT_2]MAX_OUTPUT
|
|
setp pid.z.error-previous-target true
|
|
# This setting is to limit bogus stepgen
|
|
# velocity corrections caused by position
|
|
# feedback sample time jitter.
|
|
setp pid.z.maxerror 0.000500
|
|
|
|
net z-index-enable => pid.z.index-enable
|
|
net z-enable => pid.z.enable
|
|
net z-pos-cmd => pid.z.command
|
|
net z-pos-fb => pid.z.feedback
|
|
net z-output <= pid.z.output
|
|
|
|
# Step Gen signals/setup
|
|
|
|
setp hm2_5i25.0.stepgen.02.dirsetup [JOINT_2]DIRSETUP
|
|
setp hm2_5i25.0.stepgen.02.dirhold [JOINT_2]DIRHOLD
|
|
setp hm2_5i25.0.stepgen.02.steplen [JOINT_2]STEPLEN
|
|
setp hm2_5i25.0.stepgen.02.stepspace [JOINT_2]STEPSPACE
|
|
setp hm2_5i25.0.stepgen.02.position-scale [JOINT_2]STEP_SCALE
|
|
setp hm2_5i25.0.stepgen.02.step_type 0
|
|
setp hm2_5i25.0.stepgen.02.control-type 1
|
|
setp hm2_5i25.0.stepgen.02.maxaccel [JOINT_2]STEPGEN_MAXACCEL
|
|
setp hm2_5i25.0.stepgen.02.maxvel [JOINT_2]STEPGEN_MAXVEL
|
|
|
|
# ---closedloop stepper signals---
|
|
|
|
net z-pos-cmd <= joint.2.motor-pos-cmd
|
|
net z-vel-cmd <= joint.2.vel-cmd
|
|
net z-output => hm2_5i25.0.stepgen.02.velocity-cmd
|
|
net z-pos-fb <= hm2_5i25.0.stepgen.02.position-fb
|
|
net z-pos-fb => joint.2.motor-pos-fb
|
|
net z-enable <= joint.2.amp-enable-out
|
|
net z-enable => hm2_5i25.0.stepgen.02.enable
|
|
|
|
# ---setup home / limit switch signals---
|
|
|
|
net z-home-sw => joint.2.home-sw-in
|
|
net z-neg-limit => joint.2.neg-lim-sw-in
|
|
net z-pos-limit => joint.2.pos-lim-sw-in
|
|
|
|
#*******************
|
|
# SPINDLE
|
|
#*******************
|
|
|
|
setp pid.s.Pgain [SPINDLE_0]P
|
|
setp pid.s.Igain [SPINDLE_0]I
|
|
setp pid.s.Dgain [SPINDLE_0]D
|
|
setp pid.s.bias [SPINDLE_0]BIAS
|
|
setp pid.s.FF0 [SPINDLE_0]FF0
|
|
setp pid.s.FF1 [SPINDLE_0]FF1
|
|
setp pid.s.FF2 [SPINDLE_0]FF2
|
|
setp pid.s.deadband [SPINDLE_0]DEADBAND
|
|
setp pid.s.maxoutput [SPINDLE_0]MAX_OUTPUT
|
|
setp pid.s.error-previous-target true
|
|
|
|
net spindle-index-enable => pid.s.index-enable
|
|
net spindle-enable => pid.s.enable
|
|
net spindle-vel-cmd-rpm => pid.s.command
|
|
net spindle-vel-fb-rpm => pid.s.feedback
|
|
net spindle-output <= pid.s.output
|
|
|
|
# ---setup spindle control signals---
|
|
|
|
net spindle-vel-cmd-rps <= spindle.0.speed-out-rps
|
|
net spindle-vel-cmd-rps-abs <= spindle.0.speed-out-rps-abs
|
|
net spindle-vel-cmd-rpm <= spindle.0.speed-out
|
|
net spindle-vel-cmd-rpm-abs <= spindle.0.speed-out-abs
|
|
net spindle-enable <= spindle.0.on
|
|
net spindle-cw <= spindle.0.forward
|
|
net spindle-ccw <= spindle.0.reverse
|
|
net spindle-brake <= spindle.0.brake
|
|
net spindle-revs => spindle.0.revs
|
|
net spindle-at-speed => spindle.0.at-speed
|
|
net spindle-vel-fb-rps => spindle.0.speed-in
|
|
net spindle-index-enable <=> spindle.0.index-enable
|
|
|
|
# ---Setup spindle at speed signals---
|
|
|
|
sets spindle-at-speed true
|
|
|
|
|
|
#******************************
|
|
# connect miscellaneous signals
|
|
#******************************
|
|
|
|
# ---HALUI signals---
|
|
|
|
net axis-select-x halui.axis.x.select
|
|
net jog-x-pos halui.axis.x.plus
|
|
net jog-x-neg halui.axis.x.minus
|
|
net jog-x-analog halui.axis.x.analog
|
|
net x-is-homed halui.joint.0.is-homed
|
|
net axis-select-y halui.axis.y.select
|
|
net jog-y-pos halui.axis.y.plus
|
|
net jog-y-neg halui.axis.y.minus
|
|
net jog-y-analog halui.axis.y.analog
|
|
net y-is-homed halui.joint.1.is-homed
|
|
net axis-select-z halui.axis.z.select
|
|
net jog-z-pos halui.axis.z.plus
|
|
net jog-z-neg halui.axis.z.minus
|
|
net jog-z-analog halui.axis.z.analog
|
|
net z-is-homed halui.joint.2.is-homed
|
|
net jog-selected-pos halui.axis.selected.plus
|
|
net jog-selected-neg halui.axis.selected.minus
|
|
net spindle-manual-cw halui.spindle.0.forward
|
|
net spindle-manual-ccw halui.spindle.0.reverse
|
|
net spindle-manual-stop halui.spindle.0.stop
|
|
net machine-is-on halui.machine.is-on
|
|
net jog-speed halui.axis.jog-speed
|
|
net MDI-mode halui.mode.is-mdi
|
|
|
|
# ---coolant signals---
|
|
|
|
net coolant-mist <= iocontrol.0.coolant-mist
|
|
net coolant-flood <= iocontrol.0.coolant-flood
|
|
|
|
# ---probe signal---
|
|
|
|
net probe-in => motion.probe-input
|
|
|
|
sets selected-jog-incr 0.000000
|
|
|
|
# connect feed override increments - MPG
|
|
|
|
setp halui.feed-override.direct-value false
|
|
setp halui.feed-override.scale .01
|
|
net fo-enable => halui.feed-override.count-enable
|
|
net axis-selected-count => halui.feed-override.counts
|
|
|
|
# connect max velocity override increments - MPG
|
|
|
|
setp halui.max-velocity.direct-value false
|
|
setp halui.max-velocity.scale 20.000000
|
|
net mvo-enable => halui.max-velocity.count-enable
|
|
net axis-selected-count => halui.max-velocity.counts
|
|
|
|
# connect spindle override increments - MPG
|
|
|
|
setp halui.spindle.0.override.direct-value false
|
|
setp halui.spindle.0.override.scale .01
|
|
net so-enable => halui.spindle.0.override.count-enable
|
|
net axis-selected-count => halui.spindle.0.override.counts
|
|
|
|
# ---motion control signals---
|
|
|
|
net in-position <= motion.in-position
|
|
net machine-is-enabled <= motion.motion-enabled
|
|
|
|
# ---digital in / out signals---
|
|
|
|
# ---estop signals---
|
|
|
|
net estop-out <= iocontrol.0.user-enable-out
|
|
net estop-out => iocontrol.0.emc-enable-in
|
|
|
|
# ---manual tool change signals---
|
|
|
|
net tool-change-request <= iocontrol.0.tool-change
|
|
net tool-change-confirmed => iocontrol.0.tool-changed
|
|
net tool-number <= iocontrol.0.tool-prep-number
|
|
|
|
# ---Use external manual tool change dialog---
|
|
|
|
loadusr -W hal_manualtoolchange
|
|
net tool-change-request => hal_manualtoolchange.change
|
|
net tool-change-confirmed <= hal_manualtoolchange.changed
|
|
net tool-number => hal_manualtoolchange.number
|
|
|
|
# ---ignore tool prepare requests---
|
|
net tool-prepare-loopback iocontrol.0.tool-prepare => iocontrol.0.tool-prepared
|
|
|